GE IC694TBS032

Quanzhou Xin Yuan Technology When the Gold Medal Suppliers deliver the GE IC694TBS032!

Before shipment, our dedicated personnel will test the connection of each pin. Any defective products will be directly rejected. We guarantee that your production line can be urgently repaired in one go.

Technical Specifications

Contact Configuration The module is equipped with 24 independent isolated wiring terminals, using a standard screw crimping structure. The contact material is high-conductivity copper alloy, which is corrosion-resistant and has strong vibration resistance, ensuring that the cables will not loosen after being pressed tightly.

Rated Voltage Supports a maximum continuous working voltage of 300V AC/DC. The insulation withstand voltage level is high, effectively resisting peak voltages and surge impacts in industrial environments. Rated Current The rated current capacity of a single channel is up to 2.0A. The total current carrying capacity can meet the power supply and signal transmission requirements of most medium and low-power sensors and actuators.Installation Method It adopts a standard front-insertable module design. The entire module can be pulled out and inserted without disconnecting each of the on-site cables, greatly simplifying the wiring and maintenance work in the electrical control cabinet.

Service life

The GE IC694TBS032 is extremely durable in the factory. The metal springs inside the terminal are made of high-elastic copper alloy. Even if you repeatedly plug and unplug it thousands of times, it will still hold firmly and remain powered. The outer casing is also made of flame-retardant material, resistant to aging and high temperatures. Under normal operation, it can run continuously for over ten years with ease. Moreover, its screw-wire connection design is very stable. Even if the workshop machinery shakes very hard, the wire will not loosen, and there is basically no need to worry about loose wiring causing a shutdown.
Installation and commissioning cycle

The greatest advantage of the GE IC694TBS032 module is plug-and-play with wiring. Previously, when replacing I/O modules, dozens of wires had to be removed one by one, which was time-consuming and prone to connection errors. Now, when troubleshooting, you can connect the wires and remove the module in just a few seconds to replace it with a new one, without having to rewire. This plug-and-play design directly reduces the single-point commissioning time by 80%, and the project joint commissioning progress is extremely fast.

It's really convenient.Commissioning and testing

First, test the insulation withstand voltage to ensure no leakage or breakdown; then, test the plug-and-unplug fatigue to ensure that it does not loosen no matter how many times it is disassembled and reassembled; finally, conduct full-load temperature rise tests to simulate the highest temperature and maximum current in the workshop, ensuring that it does not overheat or burn out under full-load operation. Thanks to this strict factory inspection, the equipment can basically pass all tests upon power-on without any failures.

FAQ Module

Q1 Is the installation method complex?What should be noted during the initial installation?

A1 This module adopts a combined installation method of sliding into the guide rail and front-side snap. Just push it into the slot on the base plate and it will lock. For the initial wiring, strictly follow the silk-screened instructions on the panel for cable labeling and crimping, and ensure that the terminal screws are tightened to the standard torque to prevent excessive contact resistance and overheating.

Q2 How about compatibility?Can this module directly replace the old non-intelligent modules?

A2 This module is specifically designed for the GE intelligent series motherboard, with specific bus pins and backplane protocol. It is backward compatible with some 90-30 series expansion racks, but it cannot be forcibly inserted into non-compatible series motherboards. The specific replacement requires checking your CPU model and backplane version.

Q3 inventory situation?Can it meet the sudden demands for old equipment renovation and maintenance?

A3 Quanzhou Xin Yuan Technology maintains an adequate stock of standard terminal modules on a regular basis. We are well aware of the fatal impact of component supply disruption on the production line. Relying on a strong distribution network, we ensure regular direct delivery and fully cover urgent maintenance and renovation needs.

Q4 what is the earliest delivery time?Is the logistics packaging safe?

A4 For domestic spot orders, confirmation before 1700 on the same day will result in same-day fast delivery, and within the core cities, it will be delivered the next day. For overseas urgent repair orders, through the preferred shipping routes, the customs clearance and delivery will be completed within the shortest 3-5 working days. The entire process uses the original factory anti-static vacuum and shock-proof boxes for double packaging to prevent any transportation damage.